Shenzhen DSF Science&Technology Co., Ltd.
Shenzhen DSF Science&Technology Co., Ltd. Drive Security Forward！
Add to Cart
16h 100Lm IP66 1W Anti-explosion Rechargeable Led Torch Light with ATEX
| Item | Unit | Technical Parameters | |
| Light Source | LED Power | W | 1 |
| Luminous flux | LM | 100 | |
| Lifespan | h | 100,000 | |
| Lithium Battery | Battery NO. | DSF-D01 | |
| Manufacturer | DSF | ||
| Rated Capacity | mAh | 2600 | |
| Rated Voltage | V | 3.7V | |
| Charging Time | h | ≤6 | |
| Lifespan | Circulation | 1000 Times | |
| Charger | Model | HY-055V0500A | |
| Input Voltage | V | AC100～240 | |
| Output Voltage | V | DC5.6V | |
| Output Current | A | 0.45A | |
| Lighting Time | h | 16(Weak Light) | |
| 8(Strong Light) | |||
| Effective Lighting Distance | m | 30 | |
| Working Temperature | ℃ | -20℃～+55℃ | |
| Dimension | mm | Φ33×137.7 | |
| Weight(Including Battery) | g | 182.4 | |
| Explosion-proof Mark | II 2G Ex ib op is IIC T4 Gb | ||
| IP Rate | IP66 | ||
1. Please install the special battery before use. The battery has direction, refer to Figure 1 (B), do not install the battery in an opposite direction, or the flashlight can not work properly, and not able to charge.
Initial Use: Please make sure that the battery is fully charged for over 6 hours before using. If not use for long-term, the control circuit due to the protection of the battery leaving the battery voltage cause the battery self-discharge effect, so it’s normal that the flashlight can not work before charging.
WARNING:Only use a dedicated battery (Battery Model DSF-D01), or it will bring unpredictable danger!
The charger shall be SELV or PELV certified with output voltage of maximum 5.6 V d.c.
2. Installation of Battery: With reference to Figure 1, turn (A) counterclockwise to open the tail cover, insert the battery in the direction of (B), and then turn (A) clockwise to tighten it.
Please check (C) if it’s OK before tightening (A), otherwise the IP protection level is invalid.
WARNING: Do not replace the battery or perform maintenance work in a hazardous area!
3. Work Mode ON/ OFF: Press the (E) button, the flashlight gives off hard light; then press the (E) button again, the flashlight gives low light, and then press the (E) button the 3rd time, flashlight turns off. Repeat this cycle.
4. Strobe Mode: Press (E) for 3 seconds in any state, flashlight works in Strobe Mode, and then press (E) to restore the initial state.
5. Charging: Must use the matching charger (Model: HY-055V0500A) for the flashlight, the input voltage is 100-240V.
Operation Method: Refer to Figure 1, first turn (D), let (D) round hole aligned flashlight (F) charging socket, and then insert the 3.5mm charging plug, and finally connected to the charger power supply.
If the Red Indicator Light of the Charge is on, it indicates that the battery is in charging; if the green indicator light is on, then the battery is fully charged. When the charge is complete, please turn off the charging power as soon as possible and unplug the 3.5mm charging plug, meanwhile, rotate (D) until it completely covers (F) the charging socket.
ATTENTION: (D) must be completely blocked (F) the charging socket, the proposal is to rotate (D) 90°or more, otherwise the IP protection level will be ineffective.
WARNING: Do not charge or perform maintenance work in a hazardous area!
WARNING: Must use the matching special charger, otherwise it will bring unpredictable danger!
